3D打印多孔钛合金Cage与聚醚醚酮Cage在PLIF中的疗效差异

doi:10.3760/cma.j.issn.1007-1245.2023.21.011

国际医药卫生导报 ›› 2023, Vol. 29 ›› Issue (21): 3035-3039.DOI: 10.3760/cma.j.issn.1007-1245.2023.21.011

3D打印多孔钛合金Cage与聚醚醚酮Cage在PLIF中的疗效差异

周献伟于洋刘玉峰张晓辉张文明宋健闫翔

河南省洛阳正骨医院（河南省骨科医院）骨科，洛阳　471002

收稿日期:2023-04-17 出版日期:2023-11-01 发布日期:2023-11-22
通讯作者: 于洋，Email：258955572@qq.com
基金资助:
河南省中医药科学研究专项（2019ZY1031）

Difference between 3D printed porous titanium alloy Cage and polyether ether ketone Cage in PLIF

Zhou Xianwei, Yu Yang, Liu Yufeng, Zhang Xiaohui, Zhang Wenming, Song Jian, Yan Xiang

Department of Orthopedics, Henan Luoyang Orthopedic Hospital (Henan Orthopedic Hospital), Luoyang 471002, China

Received:2023-04-17 Online:2023-11-01 Published:2023-11-22
Contact: Yu Yang, Email: 258955572@qq.com
Supported by:
Henan Special Research Project of Traditional Chinese Medicine (2019ZY1031)

摘要/Abstract

摘要：

目的　分析3D打印多孔钛合金椎间融合器（3D Cage）与聚醚醚酮椎间融合器（PEEK Cage）在后路腰椎椎间融合术（PLIF）中的疗效差异。方法　选取2021年2月至2022年2月在河南省洛阳正骨医院76例行PLIF的患者作为研究对象，根据不同的治疗方案分为观察组（38例）和对照组（38例）。其中观察组男性20例，女性18例，年龄27～76（45.67±9.69）岁；对照组男性19例，女性19例，年龄26～74（45.48±10.13）岁。观察组在PLIF下植入3D Cage，对照组在PLIF下植入PEEK Cage。在手术后对两组患者进行1年随访，比较两组的手术指标与并发症发生情况；比较两组术后3个月、6个月以及1年的椎间隙高度与椎间融合度；比较两组术后12 h与48 h的视觉模拟评分法（VAS）评分；比较两组术后3个月、6个月以及1年的Oswestry功能障碍指数（ODI）评分。使用独立样本t检验、χ²检验、秩和检验。结果　观察组的手术时间、住院时间、术中出血量、术后引流量分别为（123.26±23.62）min、（13.78±1.42）d、（316.64±26.79）ml、（342.21±33.72）ml，对照组的手术时间、住院时间、术中出血量、术后引流量分别为（124.18±23.43）min、（14.16±1.37）d、（321.36±27.63）ml、（346.38±34.17）ml，两组比较差异均无统计学意义（t=0.171、1.187、0.756、0.536，均P>0.05）；观察组术后3个月、6个月以及1年的椎间隙高度分别为（13.36±0.93）mm、（12.98±0.87）mm、（12.21±0.62）mm，均优于对照组（12.78±1.21）mm、（12.33±0.94）mm、（11.74±0.77）mm（t=2.343、3.128、2.931，均P<0.05）；观察组术后3个月、6个月以及1年的椎间融合度均优于对照组（Z=2.734、2.331、2.267，均P<0.05）；观察组术后12 h与48 h的VAS评分分别为（5.18±1.24）分、（4.23±1.12）分，均低于对照组（5.87±1.36）分、（5.06±1.21）分（t=2.311、3.013，均P<0.05）；观察组术后3个月、6个月以及1年的ODI评分分别为（24.62±6.34）分、（16.33±4.28）分、（13.69±3.27）分，均优于对照组（28.86±7.21）分、（19.66±5.87）分、（15.82±3.66）分（t=2.722、2.826、2.675，均P<0.05）。结论　两种椎间融合器在PLIF中的手术指标和术后并发症发生情况方面均无明显差异，但3D Cage能够减轻术后疼痛，更好恢复椎间隙高度以及加速椎间融合，且功能障碍情况恢复良好。

关键词:

后路腰椎椎间融合术, D打印, 多孔钛合金, 聚醚醚酮, 椎间融合器

Abstract:

Objective　To analyze the difference between 3D printed porous titanium alloy interbody fusion Cage (3D Cage) and polyether ether ketone interbody fusion cage (PEEK Cage) in posterior lumbar interbody fusion (PLIF). Methods　A total of 76 patients who planned to undergo PLIF in Henan Luoyang Orthopedic Hospital from February 2021 to February 2022 were selected as the study objects. According to different treatment plans, they were divided into an observation group (38 cases) and a control group (38 cases). In the observation group, there were 20 males and 18 females, aged 27-76 (45.67±9.69) years. In the control group, there were 19 males and 19 females, aged 26-74 (45.48±10.13) years. The observation group was implanted with 3D Cage under PLIF, and the control group was implanted with PEEK Cage under PLIF. The two groups were followed up for 1 year after surgery to compare the surgical indicators and complications. The height of intervertebral space and the degree of intervertebral fusion were compared between the two groups 3 months, 6 months, and 1 year after surgery. The Visual Analogue Scale (VAS) scores were compared between the two groups 12 h and 48 h after surgery. The Oswestry Disability Index (ODI) scores were compared between the two groups 3 months, 6 months, and 1 year after surgery. Independent sample t test, χ² test, and rank sum test were used. Results　The operation time, hospital stay, intraoperative blood loss, and postoperative drainage volume in the observation group were (123.26±23.62) min, (13.78±1.42) d, (316.64±26.79) ml, and (342.21±33.72) ml, respectively, those in the control group were (124.18±23.43) min, (14.16±1.37) d, (321.36±27.63) ml, and (346.38±34.17) ml, respectively, without statistically significant differences between the two groups (t=0.171, 1.187, 0.756, and 0.536; all P>0.05). The intervertebral space heights of the observation group 3 months, 6 months, and 1 year after surgery were (13.36±0.93) mm, (12.98±0.87) mm, and (12.21±0.62) mm, respectively, which were better than those of the control group [(12.78±1.21) mm, (12.33±0.94) mm, and (11.74±0.77) mm] (t=2.343, 3.128, and 2.931; all P<0.05). The intervertebral fusion degree of the observation group was better than that of the control group 3 months, 6 months, and 1 year after surgery (Z=2.734, 2.331, and 2.267; all P<0.05). The VAS scores in the observation group 12 h and 48 h after surgery were (5.18±1.24) and (4.23±1.12) points, respectively, which were lower than those in the control group [(5.87±1.36) and (5.06±1.21) points] (t=2.311 and 3.013, both P<0.05). The ODI scores of the observation group 3 months, 6 months, and 1 year after surgery were (24.62±6.34), (16.33±4.28), and (13.69±3.27) points, respectively, which were better than those of the control group [(28.86±7.21), (19.66±5.87), and (15.82±3.66) points] (t=2.722, 2.826, and 2.675; all P<0.05). Conclusion　There is no significant difference between the two kinds of Cage in the surgical indicators and postoperative complications of PLIF, but the 3D Cage can reduce the postoperative pain, better restore the height of the intervertebral space, and accelerate the intervertebral fusion, with good recovery of dysfunction.

Key words:

Posterior lumbar interbody fusion, 3D printing, Porous titanium alloy, Polyether ether ketone, Interbody fusion cage

周献伟于洋刘玉峰张晓辉张文明宋健闫翔.

3D打印多孔钛合金Cage与聚醚醚酮Cage在PLIF中的疗效差异 [J]. 国际医药卫生导报, 2023, 29(21): 3035-3039.

Zhou Xianwei, Yu Yang, Liu Yufeng, Zhang Xiaohui, Zhang Wenming, Song Jian, Yan Xiang.

Difference between 3D printed porous titanium alloy Cage and polyether ether ketone Cage in PLIF [J]. International Medicine and Health Guidance News, 2023, 29(21): 3035-3039.

参考文献

[1] Schnake KJ, Fleiter N, Hoffmann C, et al. PLIF surgery with titanium-coated PEEK or uncoated PEEK cages: a prospective randomised clinical and radiological study[J]. Eur Spine J, 2021, 30(1):114-121. DOI: 10.1007/s00586-020-06642-x.
[2] 孙付杰,陈山成,张振华,等.双侧椎旁肌间隙入路经椎间孔腰椎椎间融合术治疗老年退行性腰椎管狭窄症效果观察[J].国际医药卫生导报,2020,26(20):3032-3034.DOI:10.3760/cma.j.issn.1007-1245.2020.20.007.
[3] 孟海,杨雍,孙天胜,等.腰椎后路手术椎间融合器应用的专家共识[J].中国脊柱脊髓杂志,2021,31(4):379-384.DOI:10.3969/j.issn.1004-406X.2021.04.16.
[4] Macki M, Hamilton T, Haddad YW, et al. Expandable cage technology-transforaminal, anterior, and lateral lumbar interbody fusion[J]. Oper Neurosurg (Hagerstown), 2021, 21(Suppl 1):S69-S80. DOI: 10.1093/ons/opaa342.
[5] 马欢欢,仇文豪,黄浩,等.聚醚醚酮骨植入体生物改性研究进展[J].表面技术,2023,52(3):111-121.DOI:10.16490/j.cnki.issn.1001-3660.2023.03.008.
[6] Li S, Huan Y, Zhu B, et al. Research progress on the biological modifications of implant materials in 3D printed intervertebral fusion cages[J]. J Mater Sci Mater Med, 2021, 33(1):2. DOI: 10.1007/s10856-021-06609-4.
[7] Mayer F, Heider F, Haasters F, et al. Radiological and clinical outcomes after anterior cervical discectomy and fusion (ACDF) with an innovative 3D printed cellular titanium cage filled with vertebral bone marrow[J]. Biomed Res Int, 2022, 2022:6339910. DOI: 10.1155/2022/6339910.
[8] Jin YZ, Zhao B, Lu XD, et al. Mid- and long-term follow-up efficacy analysis of 3D-printed interbody fusion cages for anterior cervical discectomy and fusion[J]. Orthop Surg, 2021, 13(7):1969-1978. DOI: 10.1111/os.13005.
[9] 李建国,孙武,高春雨,等.肥胖对腰椎管狭窄症后路椎间融合术的影响[J].中国矫形外科杂志,2022,30(7):593-597.DOI:10.3977/j.issn.1005-8478.2022.07.04.
[10] 张弘来,陈宵雷,高飞.微创经皮椎弓根钉联合同切口通道减压术治疗胸腰椎爆裂性骨折的疗效与安全性研究[J].中国现代医学杂志,2023,33(5):91-96.DOI:10.3969/j.issn.1005-8982.2023.05.015.
[11] 吴军珍,浦少锋,徐永明,等.改良超声引导下脊神经后内侧支阻滞治疗腰背痛的临床研究[J].中国疼痛医学杂志,2022,28(3):193-198.DOI:10.3969/j.issn.1006-9852. 2022.03.006.
[12] Kobayashi K, Ando K, Kato F, et al. Seasonal variation in incidence and causal organism of surgical site infection after PLIF/TLIF surgery: A multicenter study[J]. J Orthop Sci, 2021, 26(4):555-559. DOI: 10.1016/j.jos.2020.05.015.
[13] Makino T, Takenaka S, Sakai Y, et al. Comparison of short-term radiographical and clinical outcomes after posterior lumbar interbody fusion with a 3D porous titanium alloy cage and a titanium-coated PEEK cage[J]. Global Spine J, 2022, 12(5):931-939. DOI: 10.1177/2192568220972334.
[14] 李艳华,何东,吴高义,等.新型骨科植入材料聚醚醚酮的研究进展[J].重庆医科大学学报,2019,44(9):1114-1117.DOI:10.13406/j.cnki.cyxb.002092.
[15] 朱超,孙超,刘绪昌,等.3 D打印椎间融合器在37例单节段腰椎手术中的应用[J].山东大学学报(医学版),2023,61(3):134-140.DOI:10.6040/j.issn.1671-7554.0.2020.1018.
[16] 王彦金,周英杰,柴旭斌,等.3D打印多孔钛合金椎间融合器与聚醚醚酮椎间融合器在后路腰椎椎间融合术中的应用研究[J].中国修复重建外科杂志,2022,36(9):1126-1131.
[17] Wu H, Shan Z, Zhao F, et al. Poor bone quality, multilevel surgery, and narrow and tall cages are associated with intraoperative endplate injuries and late-onset cage subsidence in lateral lumbar interbody fusion: a systematic review[J]. Clin Orthop Relat Res, 2022, 480(1):163-188. DOI: 10.1097/CORR.0000000000001915.
[18] 仵博宇,叶开,陈家瀚,等.3D打印聚醚醚酮/羟基磷灰石复合物的生物相容性评价[J].中国组织工程研究,2023,27(12):1932-1937.
[19] 李玉伟,王海蛟,崔巍,等.前路颈椎间盘切除3D打印微孔钛合金椎间融合器与聚醚醚酮椎间融合器椎间融合术治疗脊髓型颈椎病的疗效对比[J].中国脊柱脊髓杂志,2021,31(1):16-24.DOI:10.3969/j.issn.1004-406X.2021.01.03.
[20] 吴大鹏,万广,彭玲,等.EBM铸造多孔钛合金腰椎间融合器的可行性[J].中国老年学杂志,2021,41(3):611-615.DOI:10.3969/j.issn.1005-9202.2021.03.046.

3D打印多孔钛合金Cage与聚醚醚酮Cage在PLIF中的疗效差异

Difference between 3D printed porous titanium alloy Cage and polyether ether ketone Cage in PLIF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 4

编辑推荐

Metrics

[1]	安富荣孟冉冉. 基于医学影像学的3D打印技术结合PBL-CBL在血管疾病护理教学中的应用 [J]. 国际医药卫生导报, 2023, 29(15): 2208-2212.
[2]	王永胜, 王志强, 李书清, 周世聪, 王宗宝. 3D打印导板引导下快速锥颅软通道穿刺治疗中少量基底节区高血压脑出血的疗效分析[J]. 国际医药卫生导报, 2022, 28(4): 540-544.
[3]	张峰李玮宋远征张率功林峰沈冰王树方. 3D打印技术辅助手术治疗Schazker Ⅴ、Ⅵ型胫骨平台骨折的初步应用[J]. 国际医药卫生导报, 2022, 28(21): 3055-3059.
[4]	游慧超　李文琦　孙登江　欧阳和平. 自主3D打印技术在神经外科的应用价值探索[J]. 国际医药卫生导报, 2022, 28(13): 1801-1805.